Reset Holosun EPS Carry Red Dot: Factory Settings Guide

The Holosun EPS Carry Red Dot is a popular choice for concealed carry applications due to its small size, bright reticle, and rugged construction. Yet, like all electronic devices, it may rarely require a factory reset to correct any unexpected issues. This manual will walk you through the steps of resetting your Holosun check here EPS Carry Red Dot to its default settings.

For start, ensure your red dot sight is turned off.

Find the small reset button on the side or bottom of the sight.
Apply a small, pointed object, such as a paperclip or a thin screwdriver, to press and hold the reset button for around 5 seconds.
You will blink briefly to indicate that the reset is complete.

After the reset process is finished, turn your red dot sight back on. The reticle should now be at its default brightness and settings. Refer to the user manual for specific instructions on adjusting the settings to your preference.

Adjusting Your Holosun EPS Carry to Default Settings

Should you desire to take back your Holosun EPS Carry to its original settings, the method is fairly straightforward. First, locate the two miniature adjustment screws on the side of the sight. Then, using a small implement, gradually turn each screw counterclockwise until you arrive at the desired setting. The Holosun's instructions will provide the exact quantity of turns needed to restore to the default settings.

Restore Your Holosun EPS Carry to Default Defaults

If you've been experimenting with your Holosun EPS Carry's settings and want to go back to basics, returning it to the factory defaults is a simple process. This will wipe all of your customized settings and restore the sight to its initial state. To do this, you'll need to access the adjustment knob on the sight and follow the manufacturer's instructions. Be sure to consult your Holosun EPS Carry's manual for specific details on how to perform a factory default reset.

Performing a Factory Reset on the Holosun EPS Carry {

The Holosun EPS Carry is a popular red dot sight known for its reliability and durability. Occasionally, you might need to reset your Holosun EPS Carry to its factory settings. This can be helpful if you're experiencing issues with the sight or simply want to start fresh.

Here's a step-by-step guide on how to execute a factory reset on your Holosun EPS Carry:

Make sure the sight is disengaged.
Locate the reset button on the side of the sight. It's a small, recessed button.
Employ a thin, pointed object, such as a paper clip or a screwdriver, to activate the reset button. Hold it down for approximately 5 seconds.
You should observe a rapid flashing light sequence on the sight's display. This indicates that the reset process is underway.
Release the reset button and wait for the sight to power on normally.

Your Holosun EPS Carry has now been reset to its factory settings. You will need to re-enter any customizations or adjustments you previously made.

Reset Your Holosun for Your Holosun EPS Carry

Need to recalibrate your Holosun EPS Carry? Performing a factory reset is an easy way to bring back it to its initial settings.

This process can be helpful if you're experiencing problems with your sight or simply want to wipe clean. Here's a simple guide on how to perform a factory reset on your Holosun EPS Carry:

First, turn on your Holosun EPS Carry.
Next, locate and press the function key. Hold it down for approximately 5 seconds.
You'll see a message on the display indicating that a factory reset is being initiated.
Wait until the message disappears and your Holosun EPS Carry reboots.

Your Holosun EPS Carry is now back to its original settings. You can now adjust it according to your preferences.

Unlocking the Holosun EPS Carry: A Factory Reset Tutorial

Looking to refresh your Holosun EPS Carry sight back to its factory settings? You've come to the right place. This guide will walk you through a easy factory reset process, enabling you to correct any potential concerns and ensure your sight is functioning at its best.

Begin by locating the miniature reset button on the bottom of your Holosun EPS Carry sight. You'll need a slim object, such as a pen tip, to activate this button.
While are holding down the reset button, concurrently power on your sight. You should see the indicator flicker a few times, indicating that the factory reset is active.
Continue holding down the button for approximately 5 seconds. Then release of the button and observe your sight. It should now be reset to its factory settings.

Now, you can adjust your Holosun EPS Carry's features according to your preferences. Your sight is now ready for optimal performance.